No." General syntax or operator       -60; 09.12.92             "
001" Illegal character!\                                        "
002" Illegal command in manual model!\                          "
003" Not all required fields are programmed!\                   "
004" Input value outside limits %s and %s!\                     "
005" Wrong speed or no entry!\                                  "
006" Wrong position or no entry!\                               "
007" File %s does not exist!\ Programming                       "
008" Error initializing: insufficient memory!\  Strtup          "
009" Interpreter %s: error in header: %s\                       "
010" Interpreter %s: wrong index. line: %s\                     "
011" Interpreter %s: wrong value. line: %s\                     "
012" Edited program number outside %s and %s!\ NC PROG          "
013" NC program: illegal command!\  ErrNCIllgCmd                "
014" NC program: index outside %s and %s!\ ErrNCIllgIndex       "
015" NC program: input value outside %s and %s!\ NC prog        "
016" NC program: illegal character!\   NC prog ErrNCIllgChar    "
017" NC program: illegal operator!\  NC prog ErrNCIllgOper.     "
018" NC program: hex byte outside 00 and FF!\ NC prog           "
019" NC program: output number outside 000 and 007!\ NC prog    "
020" CAN outputs from 010 to 017 not supported yet!\            "
021" NC program: invalid assignment!\ NC prog                   "
022" Input values outside 000..007 or 010..017!\   NC prog      "
023" Line numbers not in ascending sequence!\ NC prog           "
024" After the END command further lines were edited!\          "
025" Servo module: NACK received! Error code: %d!\ UNIT SERVOMOD"
026" Servo module: check byte: calculated: %2x, received: %2x!\ "
027" NC program: error in comment or too long (max. 20)!\       "
028" NC program: no END command was edited!\ NC prog            "
029" ERROR: configuration file 'INFOS.DAT' not found!\ Init     "
030" ERROR: configuration file: not all data defined!\          "
031" Syntax error in config. file (axes, COM or language)!\     "
032" Reserved terminal error message syntax error no. 32\       "
033" Reserved terminal error message syntax error no. 33\       "
034" Reserved terminal error message syntax error no. 34\       "
035" Reserved terminal error message syntax error no. 35\       "
036" Reserved terminal error message syntax error no. 36\       "
037" Reserved terminal error message syntax error no. 37\       "
038" Reserved terminal error message syntax error no. 38\       "
039" Reserved terminal error message syntax error no. 39\       "
040" Reserved terminal error message syntax error no. 40\       "
041" Reserved terminal error message syntax error no. 41\       "
042" Reserved terminal error message syntax error no. 42\       "
043" Reserved terminal error message syntax error no. 43\       "
044" Reserved terminal error message syntax error no. 44\       "
045" Reserved terminal error message syntax error no. 45\       "
046" Reserved terminal error message syntax error no. 46\       "
047" Reserved terminal error message syntax error no. 47\       "
048" Reserved terminal error message syntax error no. 48\       "
049" Reserved terminal error message syntax error no. 49\       "
050" Program memory full\                                       "
051" Positioning module is switched off\                        "
052" Error flag index                       P%d N%d\            "
053" Wrong / error K ID\                                        "
054" K Index missing\                                           "
055" Error assignment                       P%d N%d\            "
056" Wrong K index\                                             "
057" Wrong / error T ID                     P%d N%d\            "
058" Error assignment value                 P%d N%d\            "
059" Delimiter missing ':'\                                     "
060" Wrong T index                          P%d N%d\            "
061" Wrong H index                          P%d N%d\            "
062" Wrong C index                          P%d N%d\            "
063" Wrong assignment operator              P%d N%d\            "
064" Program or line number missing         P%d N%d\            "
065" Wrong program number                   P%d N%d\            "
066" Program does not exist\                                    "
067" Wrong stop option                      P%d N%d\            "
068" Wrong output no.                       P%d N%d\            "
069" Wrong output mask                      P%d N%d\            "
070" CAN not supported yet                  P%d N%d\            "
071" Wrong output port                      P%d N%d\            "
072" Wrong A or R ID                        P%d N%d\            "
073" Wrong postion value                    P%d N%d\            "
074" Wrong speed value                      P%d N%d\            "
075" Wrong V ID                             P%d N%d\            "
076" Remote activation/deactivation not permitted\              "
077" Error program name                     P%d N%d\            "
078" Program already exists\                                    "
079" Wrong line number                      P%d N%d\            "
080" Program does not exist\                                    "
081" Illegal command                        P%d N%d\            "
082" Wrong program or line number           P%d N%d\            "
083" Error ID ')'                           P%d N%d\            "
084" Error comparing                        P%d N%d\            "
085" Wrong input no.                        P%d N%d\            "
086" Wrong input port                       P%d N%d\            "
087" Error ID '('                           P%d N%d\            "
088" Wrong comparison value                 P%d N%d\            "
089" Only comparison with 0 permitted       P%d N%d\            "
090" Wrong Z index                          P%d N%d\            "
091" Wrong WAIT command                     P%d N%d\            "
092" Wrong time                             P%d N%d\            "
093" Unknown command                        P%d N%d\            "
094" Wrong M index                          P%d N%d\            "
095" Axis module not in manual mode\                            "
096" Error programming flash EPROM\                             "
097" No data transmission allowed in this operating model\      "
098" Transmission checksum error\                               "